It looks like what you see here. While you have the drive off, you can also check the condition of the gimbal bearing and check the baffels. Most other stands on the market today you have to remove the drive from the stand and turn the drive around and replace the drive back onto the stand to perform work and do it all over again when you want to reinstall the drive. I also have Alpha drives not sure if it works with bigger drives. Sharps-Nut Re: Building an Outdrive Stand The end pieces were 12x12 to start with.
Connected them at each end with scewed in 2x4s and then ran 4 pieces of 2x4s up as legs. I am not going to paint some floral design on it. That puts most of the weight on the front wheels. Com Our Certified Technicians are trained to make sure you get the right parts and tools. I don't have a link for that one. Pulling the drive is not rocket science. I actually bought a U-pod, the yellow plastic stand on the right.
The feedback on all units sold has been 100% positive. Brand New StumpysFabWorks boat lower unit jack. I made these much closer to each other than the base. Get fast accurate answers to almost any Mercruiser related question. Known for their performance and reliability, it is easy to take your MerCruiser sterndrive, made by one of the industry leaders, for granted.
I made mine big enough for any drive I may run into. You can perform maintenance on your drive with the drive stand on the ground or with the casters removed these stands can be bolted to your bench top for a more permanent repair station. I left just enough room between them to slide the outdrive into the slot and it will be supported by the cav plate. Perform expert tune-up's Troubleshoot and Diagnose all on your own. But the ebay one probably is easier to get under the outdrive, and balances better. I am not responsible for misfitment do to incorrect measurements. The stand features scratch-preventing sheaths to ensure that outdrives are well protected during transport.
I welded the fork on mine at a slight reaward angle, so when the weight of the drive is on it, it is just about level. Like all my Items, Made With Pride in the U S A! I am considering putting pneumatic wheels on it, but right now, it works perfectly. Founded in 2005, it is the largest collection of Sea Ray information on the internet. Gear oil must also be checked regularly. Instead of working on one drive at a time, I needed to work on my two drives side by side, to compare wear and tear. These stands are made of steel tubing and weigh approximately 75 pounds. I can't resist posting my improvised stand.
Back out the plug until it loosens and some oil starts to run out. I just placed an order for two of them. I went as cheap as I could with mine. Maintain your drive like an expert! These can corrode through a process called galvanization. Raise the drive and inspect them looking for signs of cracking and fouling.
Mercruiser Engine Parts For fishing, boating, boat racing, and watersport activities, the MerCruiser sterndrive provides ample power for every boating activity. When not in use these can be stacked for storage. I believe there is another stand on the market that claims to not have this issue. The height is adjustable with the hand crank and you should not have any issues pulling your Bravo off. I am considering putting pneumatic wheels on it, but right now, it works perfectly.
A cheap way to store your high dollar outdrive without laying it on the ground. They'll make moving them around during the winter storage period a lot easier. Re: Building an Outdrive Stand I made a stand out of a couple 2x6 and 2x4s that I had laying around. Take off 6 nuts on a Mercruiser Bravo 1 and pull. Your better off buying them. It holds the drive upright and upside down. I also build a stand like this, but it is adjustable to support any brand of outdrive including the Mercruiser 6.
Two nylon bolts help keep outdrives upright and stable. Make the bottom a reciever style to where you can reinstall your engine stand uprite or the outdrive jack. I welded the fork on mine at a slight reaward angle, so when the weight of the drive is on it, it is just about level. Hope that gets you a general idea. I am considering putting pneumatic wheels on it, but right now, it works perfectly.
Regardless of its name, corrosion must be avoided. Please take a moment to donate now. It is designed to fit almost every outdrive available. Since it was custom made and at the right height, I will be able to slide the drive back in. The top of the jack is lower than the top of all drives to allow use under most all swim platforms.